FIELD MANUAL // M-VAVE FM-1

USER GUIDE

A practical, hands-on field manual for playing, shaping, and patching Ruido.

00 // OVERVIEW

↑ INDEX

Ruido is open-source custom firmware that turns the M-VAVE FM-1 into a four-voice CMOS drone and noise synthesizer, built as a dry stereo sound source for guitar pedals and Eurorack. Instead of playing chromatic piano notes or sequences, four coupled oscillators and resonant filters run continuously while you shape rail coupling, modulation, scene morphs, and finger pressure in real time.

01 // GUIDE CONVENTIONS

↑ INDEX

Notation used throughout this manual:

02 // HARDWARE OVERVIEW

↑ INDEX

2.1 CONNECTIONS

All connections and the power switch run along the top edge of the chassis.

  • HEADPHONES / LINE OUT 3.5 MM STEREO

    3.5 mm stereo output for headphones, pedals, mixer, or Eurorack modular gear.

  • MIDI IN 3.5 MM TYPE-A

    3.5 mm mini-jack input for external MIDI tempo clock and start/stop transport.

  • USB-C AUDIO + POWER

    Charges the internal battery, streams stereo digital audio and MIDI to a computer or tablet, and updates firmware.

  • POWER ON / OFF SWITCH

    Switches the unit on and off.

2.2 FRONT PANEL

All controls are direct and accessible without nested menus.

Annotated top-down diagram of the M-VAVE FM-1 front panel mapped to Ruido controls: Master is Volume, Select is Zoom or Step, Presets is Scene Morph, Algorithm is Rail Coupling, Knobs 1 to 4 control Voices 1 to 4 and screen parameters, OCT- and OCT+ are Fine and Coarse knob gears, FX is Filters, SEL is Keyboards, LFO is Modulation, EDIT is Voice Mixer, GLO is Global Settings, HOME is Oscillators, SAVE is Scenes, PLAY/STOP is Audio On/Off, unused buttons ENV, ARP, SEQ, and REC are dimmed, the left 20 keys are 20 Pressure Keys, MONO is Latch, POLY is Tap, the top-right key is Shift, and Keys 13 to 16 are Mute 1 to 4.
M-VAVE FM-1 · RUIDO CONTROL MAP (DIMMED BUTTONS UNUSED)
  1. 01.MASTER

    Sets analog output volume.

  2. 02.SELECT

    Zooms the idle oscilloscope waveform, steps through voices, LFO slots, and settings, or selects between the three keyboards.

  3. 03.PRESETS

    Morphs continuously from one saved scene to the next in a loop (1 → 2 → 3 → 4 → 1), skipping empty slots.

  4. 04.ALGORITHM

    Sags the shared virtual power rail so the four voices pull into chorus and hard sync; hold Shift (the lit top-right key) while turning to set master tempo.

  5. 05.KNOB1–KNOB4

    Tunes voices 1–4 from the clean scope, or adjusts the four parameters along the bottom of the screen.

  6. 06.OCT- / OCT+

    Momentary rate gears. Hold [OCT-] while turning any knob for fine adjustments, or hold [OCT+] for fast full-range sweeps.

  7. 07.MODE BUTTONS

    Open Filters [FX], Keyboards [SEL], Modulation [LFO], or Voice Mixer [EDIT]; press again to cycle voices, keyboards, LFOs, or views. Press [GLO] to open or close Global Settings.

  8. 08.HOME, SAVE & PLAY

    [HOME] returns to the clean scope (press multiple times to cycle Frequency, Duty, and Drift), [SAVE] steps through Store and Delete Scene, and [PLAY/STOP] toggles audio output.

  9. 09.27-KEY SURFACE

    The left 20 keys, OP1–GLO and bottom-row Keys 1–12, respond continuously to finger pressure. On the right, MONO latches held keys, POLY taps tempo in Rhythm Lab, Keys 13–16 mute voices 1–4, and the lit top-right key is Shift.

03 // GET STARTED

↑ INDEX

3.1 POWER & AUDIO SETUP

  1. 01.CONNECT AUDIO

    Set (MASTER) low and plug headphones or a 3.5 mm TRS stereo breakout cable into the output jack (avoid plugging a mono 3.5 mm TS cable directly into the stereo jack).

  2. 02.SWITCH ON

    Flip the power switch on the top edge of the chassis. Ruido boots with audio output stopped so startup never pops or blasts your monitors.

  3. 03.PRESS PLAY & RAISE VOLUME

    Press [PLAY/STOP] to start the four-voice drone and raise (MASTER) gradually; press [PLAY/STOP] anytime to fade output on or off.

3.2 BUILD YOUR FIRST DRONE

  1. 01.TUNE A CHORD

    Open Oscillators with [HOME] and turn (KNOB1)–(KNOB4) to set a low root note and three close harmonies; hold [OCT-] while turning to find slow, warm beating.

  2. 02.ADD RAIL COUPLING

    Turn (ALGORITHM) to around 40% so close pitches pull into chorus, then turn past 45% to hear voices tug and lock into hard sync.

  3. 03.SCULPT THE FILTERS

    Open Filters with [FX], turn (SELECT) to select voice 1 and roll (KNOB3) down for deep bass; select voice 2 and raise (KNOB4) until the filter begins to sing.

  4. 04.ADD SLOW MOTION

    Open Modulation with [LFO], set (KNOB1) to LPF, choose a smooth wave on (KNOB2), keep rate slow on (KNOB3), and raise depth on (KNOB4) so the filter breathes on its own.

  5. 05.LEAN INTO THE KEYS

    Select Live Mixer with [SEL], then press Keys 1–4 on the bottom left to open and close each voice's filter by finger pressure.

  6. 06.SAVE YOUR SCENE

    Tap [SAVE], then tap one of the four blinking scene keys, Keys 9–12, on the bottom row to store your patch.

04 // HOW RUIDO WORKS

↑ INDEX

Each of the four voices runs through an identical signal path into the stereo mix:

Ruido synthesizer signal flow: inside each of the four voices, a pulse oscillator coupled to a shared top V+ power rail passes through a pre-filter drive gain stage, series high-pass and low-pass filters, VCA gain stage, and stereo pan splitter into left and right summing buses and stereo outputs, modulated from below by per-voice dual LFOs, three keyboards, and four morphing scenes.
SOLID: AUDIO & V+ RAIL · DASHED: MODULATION & CONTROL
  1. 4.1VOICE & POWER RAIL

    Four pulse oscillators run continuously in parallel without note triggers or envelopes, coupled through a shared V+ power rail that pulls voices into chorus and hard sync as it sags. Each voice passes through pre-filter drive, series high-pass and low-pass filters, a VCA, and stereo pan into the master mix.

  2. 4.2MODULATION & SCENE MORPHING

    Each voice has two LFOs (A and B) reaching into audio rate to modulate pitch, duty, filters, level, or pan, and LFO B can also cross-modulate LFO A. Four scenes store the full patch state for continuous loop morphing or live pressure blending.

  3. 4.3PRESSURE KEYBED & UTILITY SWITCHES

    Instead of triggering chromatic notes, the left 20 keys respond continuously to finger pressure across three selectable keyboards and return to the resting patch on release. The seven right-side keys act as dedicated switches for latch, tap tempo, voice mutes, and a shift modifier.

05 // THE SCREEN

↑ INDEX

The display is divided into three horizontal zones:

Ruido Oscillators Frequency screen divided by dashed area outlines into three horizontal zones: the top status bar, the center four-voice waveform, and the bottom four-knob slider strip
OSCILLATORS · FREQUENCY VIEW
  1. 5.1TOP BAR

    Shows the current page on the left and status readouts on the right. Adjusting other controls updates this bar briefly without closing your open page.

  2. 5.2CENTER VIEW

    Shows the live four-voice waveform, or the active page's view when open. Quick adjustments from the clean scope appear briefly and fade out on their own.

  3. 5.3BOTTOM STRIP

    Maps four sliders and live values directly to (KNOB1)–(KNOB4). When a view does not use the four knobs, this strip shows short control hints instead.

06 // MODES

↑ INDEX

6.1 OSCILLATORS

[HOME] sets pitch, pulse width, and analog drift across all four voices, and returns to the clean scope from any open page.

Ruido Oscillators Frequency view showing four coupled oscilloscope traces, OSC 1 to OSC 4 frequency sliders, and three modulation dots under each voice
OSCILLATORS · FREQUENCY VIEW
  1. 01.FREQUENCY

    Tunes voices 1–4 from slow sub-audio pulses (0.05 Hz) up to 20 kHz. Three dots under each voice indicate active filter and LFO modulation.

  2. 02.DUTY

    Adjusts pulse width from 5% to 95% around a hollow 50% square wave, thinning the tone without shifting pitch.

  3. 03.DRIFT

    Adds independent analog-style pitch wander per voice, from locked pitch (0%) to wide drift (100%).

6.2 VOICE MIXER

[EDIT] balances volume, pre-filter drive, and stereo placement across all four voices.

Ruido Voice Mixer Level view displaying four vertical voice level bars with overdrive saturation above 70 percent and modulation dots below each voice
VOICE MIXER · LEVEL VIEW
  1. 01.LEVEL

    Sets clean voice volume from 0–70%, then adds up to 4.5x pre-filter overdrive from 70–100%.

  2. 02.PAN

    Places voices 1–4 across the stereo field from L100 to R100. Turning (SELECT) switches output routing between Stereo and Mono.

6.3 FILTERS

[FX] shapes one voice at a time through series 12 dB/oct high-pass and low-pass filters; turn (SELECT) to choose voice 1–4.

Ruido Filter screen displaying a dual-peak passband curve for Oscillator 1 with HPF, HP RES, LPF, and LP RES controls
FILTERS · PASSBAND VIEW
  1. 01.HPF

    Cuts low frequencies from 2 Hz up to 28 kHz to tighten bass or isolate upper harmonics.

  2. 02.HP RES

    Boosts a resonant peak at the high-pass cutoff, self-oscillating and driving into diode clipping at higher levels.

  3. 03.LPF

    Rolls off high frequencies from 28 kHz down to 2 Hz for darker, warmer drones.

  4. 04.LP RES

    Boosts a resonant peak at the low-pass cutoff, self-oscillating into a sine tone and driving into diode clipping at higher levels.

6.4 MODULATION

[LFO] provides two independent modulators per voice; turn (SELECT) to choose any of the eight slots (A1–B4).

Ruido LFO A1 screen showing an active triangle modulation wave with Target, Shape, Rate, and Depth controls
MODULATION · WAVEFORM VIEW
  1. 01.TARGET

    Chooses the modulated parameter: pitch, duty, filter cutoff or resonance, level, or pan. LFO B can also modulate LFO A's rate or depth.

  2. 02.SHAPE

    Morphs continuously across sine, triangle, sawtooth, square, and smooth random waves.

  3. 03.RATE

    Sweeps speed from slow 0.01 Hz cycles up to 2 kHz audio-rate modulation.

  4. 04.DEPTH

    Sets modulation intensity from 0% (bypassed) to 100%.

6.5 GLOBAL SETTINGS

[GLO] opens and closes device settings; turn (SELECT) to pick a row and (ALGORITHM) to change it.

Ruido Global Settings menu screen showing row 1 of 9 with Output Routing, Key Sensitivity, Mute Mode, Scene Mode, MIDI Clock In, and MIDI Transport In
GLOBAL SETTINGS · MENU VIEW
  1. 01.OUTPUT ROUTING

    Switches the main output between Stereo and Mono.

  2. 02.KEY SENSITIVITY

    Adjusts key pressure response in five steps from Very High to Very Low; pressing a pressure key on this row shows a live force meter.

  3. 03.MUTE MODE

    Chooses Momentary or Latching behavior for the voice mute and solo keys.

  4. 04.SCENE MODE

    Chooses Latching or Momentary behavior when recalling scenes from the keybed.

  5. 05.MIDI CLOCK IN

    Locks automatically to incoming 24 PPQN MIDI clock, or runs on internal clock when set to Off.

  6. 06.MIDI TRANSPORT IN

    Sets MIDI Start and Stop messages to Off, Phase (resets bar phase on Start), or Run/Stop (starts and mutes audio).

  7. 07.MIDI CHANNEL IN

    Receives on all MIDI channels (Omni) or a single channel (1–16).

  8. 08.FACTORY RESET

    Restores Factory Presets (default patch, scenes, and settings) or Clean Init (unmodulated patch and empty scenes).

  9. 09.ABOUT

    Displays firmware version, author credits, and license information.

07 // KEYBOARDS

↑ INDEX

[SEL] switches the pressure keys between three keyboards; you can also turn (SELECT) to step through them.

7.1 COMMON CONTROLS

The right-side utility keys stay active across all three keyboards.

Ruido generic keyboard diagram highlighting the right-side utility keys labeled Latch, Shift, and Mute
KEYBOARD · COMMON CONTROLS
  1. 01.SHIFT

    Shift stays lit at the top right to access voice solo, scene recall, tempo, and keyboard selection.

  2. 02.LATCH

    Holds any pressed pressure keys hands-free until tapped again or switched to another keyboard. Printed on the keybed as MONO.

  3. 03.MUTE

    Keys 13–16 mute or unmute voices 1–4, using Momentary or Latching mode set in Global Settings [GLO].

7.2 LIVE MIXER

Shapes mix balance, filtering, harmonic intervals, and stereo width in real time.

Ruido Keyboard 1 of 3 Live Mixer map showing Tone, Filter, Width, Latch, and Shift above the keybed and Filter, Octave, Duty, and Mute below
KEYBOARD 1/3 · LIVE MIXER
  1. 01.TONE

    Adds overdrive and rail coupling, drops sub-octaves, or locks harmonic ratios.

  2. 02.FILTER

    Sweeps resonant low-pass and high-pass filters across the full mix.

  3. 03.WIDTH

    Pulls voices to unison, adds chorus detune, or widens stereo spread.

  4. 04.FILTER

    Sweeps per-voice formant peaks, or swells muted voices in smoothly.

  5. 05.OCTAVE

    Bends individual voices up one to two octaves.

  6. 06.DUTY

    Narrows individual pulse widths toward a thin pulse.

7.3 CIRCUIT LAB

Bends the oscillator circuits with rail starvation, cross-modulation, wavefolding, and clock crush.

Ruido Keyboard 2 of 3 Circuit Lab map showing Mod, Lock, Bends, Latch, and Shift above the keybed and Cross, Fold, Crush, and Mute below
KEYBOARD 2/3 · CIRCUIT LAB
  1. 01.MOD

    Starves the power rail, ring-modulates voice pairs, or pushes LFOs into audio rate.

  2. 02.LOCK

    Drives filters into self-oscillation or hard-syncs voices 2–4 to voice 1.

  3. 03.BENDS

    Scatters tuning and pan, adds sub-octave XOR, or feeds the mix back into drive.

  4. 04.CROSS

    Patches each voice's neighbor into pitch FM and XOR cross-modulation.

  5. 05.FOLD

    Routes each voice through a multi-stage wavefolder.

  6. 06.CRUSH

    Reduces sample rate with sub-octave grit per voice.

7.4 RHYTHM LAB

Turns the continuous drone into rhythmic pulses, clock divisions, and Euclidean patterns.

Ruido Keyboard 3 of 3 Rhythm Lab map showing Pulse, Gate, FX, Latch, Tap, and Shift above the keybed and Stutter, Divide, Euclid, and Mute below
KEYBOARD 3/3 · RHYTHM LAB
  1. 01.PULSE

    Adds quarter-note ducking pump, a four-voice chase, or up to 4x clock speed.

  2. 02.GATE

    Shapes active gates into resonant filter plucks or short percussive clicks.

  3. 03.FX

    Adds off-beat shuffle, stereo ping-pong alternation, or rapid gate rolls.

  4. 04.TAP

    Pulses on the beat and sets tempo by tapping. Printed on the keybed as POLY.

  5. 05.STUTTER

    Runs unsynced vactrol-style stutters per voice.

  6. 06.DIVIDE

    Triggers tempo-synced polyrhythmic clock divisions per voice.

  7. 07.EUCLID

    Generates phase-offset 16-step Euclidean rhythms per voice.

08 // SCENES

↑ INDEX

Four scene slots save complete patches that you can recall, blend, or morph live.

Ruido Store Scene screen showing slots 1 to 4 status above the keybed diagram with Keys 9 to 12 highlighted as the Scene zone
SCENES · STORE SCENE
8.1STORE

Press [SAVE], then tap one of Keys 9–12 to save your current sound.

Ruido Delete Scene screen showing slots 1 to 4 status above the keybed diagram with Keys 9 to 12 highlighted for clearing a saved scene
SCENES · DELETE SCENE
8.2DELETE

From Store Scene, press [SAVE] again or turn (SELECT), then tap one of Keys 9–12 to clear that scene.

8.3RECALL

Hold Shift and tap one of Keys 9–12 to switch directly to that scene.

8.4BLEND

Hold Shift and press two or more of Keys 9–12 together to blend scenes by finger pressure.

8.5MORPH

Turn (PRESETS) to morph smoothly through your saved scenes in a loop (1 → 2 → 3 → 4 → 1), skipping empty slots.

TIP:Factory Scenes 2–4 are built to showcase each keyboard: pair Scene 2 with Live Mixer, Scene 3 with Circuit Lab, and Scene 4 with Rhythm Lab.

09 // CONTROLS & COMBOS

↑ INDEX

9.1 RAIL COUPLING

(ALGORITHM) controls how strongly the four oscillators pull and starve each other across their shared power rail.

Ruido Rail Coupling screen at 85 percent showing the starved shared power rail above four phase-locked oscillator ramps
RAIL COUPLING · STARVED VIEW
  1. 01.SOFT PULL

    From 0–45%, nudges close voice pitches into warm analog-style chorus and phase locking.

  2. 02.HARD SYNC

    Past 45%, starves the virtual rail so voices sag in pitch, skew pulse width, and snap into subharmonic hard sync.

9.2 KNOB SPEED

[OCT-] and [OCT+] act as momentary speed gears while turning (KNOB1)–(KNOB4), (ALGORITHM), or (PRESETS).

  1. 01.FINE

    Holding [OCT-] slows knob response for micro-tuning intervals, 0.1 BPM tempo steps, and subtle scene morphs.

  2. 02.COARSE

    Holding [OCT+] speeds knob response to sweep a full range in under two turns or step whole scenes on (PRESETS).

9.3 SHIFT

Holding Shift opens an on-screen map of secondary controls playable from any page.

Ruido Shift map screen highlighting Keyboard on Select and OP1 to OP3, Tempo on Algorithm, Scene on Keys 9 to 12, and Solo on Keys 13 to 16
SHIFT · CONTROL MAP
  1. 01.KEYBOARD

    Switches between the three keyboards by turning (SELECT) or tapping the first three top-left keys, printed on the keybed as OP1–OP3.

  2. 02.TEMPO

    Adjusts internal master tempo from 20 to 3,000 BPM on (ALGORITHM), or shows EXT when synced to incoming MIDI clock.

  3. 03.SCENE

    Recalls a saved scene on Keys 9–12, or blends multiple scenes by finger pressure when pressed together.

  4. 04.SOLO

    Isolates voices 1–4 on Keys 13–16, using Momentary or Latching mode set in Global Settings [GLO].

10 // HOW TO

↑ INDEX

10.1 SWELL A MUTED VOICE

On Live Mixer, muting a voice turns its Filter key into a pressure-controlled swell gate.

  1. 1. Open Global Settings with [GLO] and set Mute Mode to Latching.
  2. 2. Select Live Mixer with [SEL] and tap one of Keys 13–16 to mute a voice.
  3. 3. Press that voice's Filter key on Keys 1–4 to fade it in and out by finger pressure.

10.2 TURN A VOICE INTO DRUM PINGS

Below 1 Hz, an oscillator stops producing a steady pitch and fires slow clicks into its filter.

  1. 1. Open Oscillators with [HOME] and lower a voice below 1 Hz until it clicks slowly.
  2. 2. Open Filters with [FX], select that voice, and set the low-pass cutoff in the bass range.
  3. 3. Raise low-pass resonance just below self-oscillation so each click rings and decays.

10.3 CROSS-MODULATE TWO LFOS

Each voice has two LFOs, and LFO B can modulate LFO A's rate or depth.

  1. 1. Open Modulation with [LFO] and set LFO A on any voice to sweep pitch or filter cutoff.
  2. 2. Select LFO B on the same voice and set its target to LFO A's rate or depth.
  3. 3. Choose a slow wave and raise depth so LFO A's motion never repeats.

10.4 SYNC RHYTHM LAB TO EXTERNAL MIDI

With MIDI Clock In set to Auto in Global Settings, Ruido locks automatically to incoming clock.

  1. 1. Send MIDI clock over 3.5 mm TRS or USB-C.
  2. 2. Select Rhythm Lab with [SEL].
  3. 3. Hold any Divide key on Keys 5–8 or Euclid key on Keys 9–12 to gate voices in time.

11 // FAQ

↑ INDEX
Is flashing Ruido safe, and can I revert to the factory M-VAVE firmware?

Yes. Ruido writes only to the application slot and leaves the factory boot sector untouched, so you can revert to stock M-VAVE firmware on The Firmware Hub at any time. If an update is ever interrupted, hold [OCT-] while switching power on to enter USB rescue mode.

Does Ruido output digital audio over USB-C as well as the 3.5 mm analog jack?

Yes. Alongside the 3.5 mm analog output, Ruido streams class-compliant 44.1 / 48 kHz stereo digital audio over USB-C to macOS, Windows, Linux, iOS, and standalone USB hosts.

Can I plug Ruido straight into a mono guitar pedalboard?

Yes. Use a 3.5 mm TRS stereo to dual 1/4" TS breakout cable rather than plugging a mono 3.5 mm TS cable directly into the stereo jack, then open Global Settings with [GLO] and set Output Routing to Mono.

Why don't ENV, ARP, SEQ, and REC do anything?

Ruido omits envelopes, arpeggiators, and step sequencers by design, so [ENV], [ARP], [SEQ], and [REC] stay unlit and unassigned on the front panel.

How can I avoid stepping from the knob detents?

Hold [OCT-] while turning any knob for fine adjustments, or use the pressure keys and open Modulation with [LFO] to sweep pitch and filters smoothly.

Why square and pulse waves instead of wavetables or multiple shapes?

Physical CD40106 oscillators couple and hard-sync across a shared power rail because of their sharp switching edges. Acoustically, 50% square waves contain only odd harmonics, leaving open frequency space for fuzz and distortion pedals without intermodulation mud.

Why doesn't Ruido include built-in digital reverb or delay?

Ruido puts all of its DSP into 4x oversampling and per-voice high-pass and low-pass Sallen-Key filters, so external guitar pedals and Eurorack modules get an alias-free signal.

FIRMWARE INSTALLATION

PLUG IN. FLASH RUIDO.

Flash over USB-C from Chrome, Edge, or Brave. Free and open-source.